In the past, automatic transmission swaps were normally done so the tranny would handle the extra power of a new (or bigger) engine combination. Rarely, if ever, were gear ratios or the benefits of overdrive a consideration for the general street enthusiast. Now, with a bunch of choices out there, overdrive transmissions are quickly becoming known for producing many more benefits, aside from just fuel mileage, and we're about to show you why.
Enter Randy Manning, an outside sales representative for Edelbrock. His daily driver, a '70 El Camino also happens to be his favorite toy. What's more, this long-time enthusiast of speed has installed plenty of trick upgrades on this proven performer. Check out our Tech Specs box to see what powers his hauler. Then, we'll tell you why he thought this swap was a great idea.
After hearing so much about the benefits of GM's newer transmissions, Randy felt that swapping out the trusty TH400 would offer a better level of driveability, more favorable gear ratio splits, and maybe even an increase in fuel economy. He chose a Hughes Performance 4L60 (not to be confused with the 4L60E), which is an updated version of the popular 700R4. What we're focusing on here is more of the "meat and potatoes," as opposed to a step-by-step install. We figure most of you are already familiar with the basic "how-to" wrench-turning parts of this swap.
After removing the driveshaft, exhaust system and related components, the trusty TH400 was
|ASSORTED COMPARISONS AND CONSIDERATIONS LOW GEAR RATIOS |
|TH350 ||TH400 ||4L60 |
|2.52:1 ||2.48:1 ||3.00:1 |
In crunching the numbers above, the 4L60 delivers at both ends. The 3.00:1 low-gear ratio launches harder, but when coupled with its .67 overdrive represents a 33-percent reduction from 1:1 for highway cruising. To break it down further, when you consider that the El Camino has a 3.73:1 rear gear, this 4L60 delivers the low-gear performance of a TH350 with a 4.44:1 rear, or, a TH400 with a 4.51:1 rearend ratio. In overdrive mode, the 4L60 performs like a TH350 (TH400 or Powerglide) with a 2.50:1 ring-and-pinion!
|CRUISE TEST—RPM AT 70 MPH |
|TH400 ||4L60 |
|3,300 ||2,200 |
The drop in cruise rpm represents more than improved fuel economy (from 13 to almost 18 mpg); it also reduces strain and friction on engine internals. Anybody who has cruised a considerable distance with a performance car equipped with aftermarket exhaust and a relatively low rearend gear knows what the interior noise levels are-hell, most times you can't carry on a conversation, much less hear the stereo. Swap in a 4L60, and you might find your comfort zone has gone up several notches. Another great trick from Hughes is their 10-inch performance lockup converter. It provides more stall down low, but it locks up on the road for another 100-200 rpm, as opposed to the TH400's larger, "street performance" converter.
Transmission Swap News And Notes* 700R4 and 4L60 use the same yoke as the TH350 (smaller than the TH400).* Driveshaft needs to be shortened (measure from the back of the tailshaft, or flat transmission rear seal surface, to the flat of your pinion flange (at, or as close to ride height as possible).* Transmission cooler lines fit with minor realignment.* Speedometer cable requires no modification. Hooks right up!* Transmission case is slightly larger on 4L60 (no clearance problems on this El Camino-could be tight in other applications).
How To Make It HookWith an El Camino that just had an infusion of more low gear, it was obvious that producing favorable test results would have a great deal to do with traction. The biggest fear was having an empty pickup bed-as in no weight over the rear axle with a limited amount of options to make it stick on the starting line. We turned to BFGoodrich for a set of their 275/60R15s Comp T/A Drag Radials.BFGoodrich has been manufacturing its Comp T/A Drag Radial for several years now, with proven results. Targeted specifically for the Street-Legal drag racing crowd, the tire met with rave reviews. With its minimal tread, few cross grooves, and softer compound, the Comp T/A Drag Radial is yet another tool to be used in your arsenal of speed, and it's available in sizes ranging from P295/65R15 to P315/35R17.Referring to the Drag Strip Results chart, the improvement in 60-foot times are eye opening. Three-tenths is a bunch, when you realize that's a figure you can't count on your watch, and lately, an entire 16-car NHRA Pro Stock field has less of a spread from the first to the last qualifier. So, if you're looking to improve traction at the drag strip, opt for a new set of shoes!
The old TH400 is shown in the foreground, right next to the new Hughes 4L60 and our assort
We put a straight edge at the back of each tailshaft to demonstrate the slight difference
In this photo, the straight edge shows the difference in the location of the transmission
Always double check your converter fitment before trying to bolt up the trans and converte
* Transmission crossmember needs to be moved forward from TH400 location (rearward from TH350 or Powerglide). This El Camino had multiple crossmember mounting holes from the factory, already there for different combinations. Even so, we did have to drill and tap two new holes.
* If using a single-pattern flexplate, be sure it matches the bolt pattern on your converter before installing the transmission. Dual-pattern flexplates should not be a problem, though you may consider using one that's SFI approved.
* Proper adjustment of the TV (throttle valve) cable is the most important part of this swap. The TV cable performs the functions of both transmission kickdown and line pressure. Follow the factory instructions to the letter, or call the Hughes Tech Line if you're in doubt. You can fry the transmission in no time at all, if this adjustment isn't done properly. The TV cable resembles those used on a TH350, but the 4L60 cable does a lot more. We can't over emphasize the importance of this step.
Once our flexplate and other clearance issues were double checked, the new 4L60 was jacked
* Another key item is properly setting the vacuum modulator. Here again, Hughes supplies easy-to-follow instructions.
* Wiring for the lockup converter is simple: one 12-volt, "key-on" wire to the front, driver's side terminal of the factory plug.
Additional needs:* Three, 1-1/4 X 5/16-inch Grade-8 bolts and locknuts for the torque converter* A 4L60/700R4 dipstick and tube* For aftermarket or Factory shifters, you'll need two metric pan bolts (longer than those supplied with the transmission).
More Numbers To DigestThe Drag Strip Results chart (right) chronicles three runs from late last year with the old TH400 transmission-using both street and BFG Comp T/A Drag Radial tires, and slightly different driving styles. Please note; the best 60-foot time from that outing was 2.02 seconds with a quarter-mile clocking of 13.053 at 106.89 mph. Not too shabby. With his new Hughes Performance 4L60 transmission, Manning ran a 1.89 60-foot time, with a best of 12.82 at 106.90 mph. During his track testing at the end of March, Manning made what most racers would consider "normal" adjustments-tire pressure, length of burnout, and launch rpm.
In conclusion, the net yields include a 60-foot improvement of .34 and a quarter-mile betterment of .225 seconds. Couple that with two days of general driving, which included in-town and freeway (stop and go and just plain go), as well as two demonstration, full-throttle blasts for some clients. At the end of that unofficial fuel test, the consumption came out to 17.8 mpg! Just imagine what constant freeway speeds would yield. We're guessing well over 20 mpg.
Seeing as how most performance-minded folks are of the curious nature, we estimate a swap like this would fall between the $1,500 to $3,000 range, depending on sources, converter selection, accessories, etc. However, please be aware of the fact that your intentions are always best served by dealing with a reputable "high-performance minded" company, for the maximum results and benefits.
This is where bad turns to good (in this case, at least). With a difference in the overall
Here's one of those common sense steps we're happy to pass along. Before any automatic tra
Your new driveshaft dimension is a critical measurement, too. To simulate ride height, we
The "fickle finger of fate" is pointing to the TV cable bracket, better known as the most
Randy chose a B&M Pro Ratchet shifter to click through the gears with. Along with it came
|TECH SPECS (before trans swap) |
|Engine || |
383 stroker, four-bolt mains, Scat crank, Crower 6-inch rods, Milodon oil pan, ARP main and head studs, SRP pistons, Edelbrock RPM cam (234 intake, 244 exhaust duration at .050-inch lift and .488 intake and .510 exhaust lift), Edelbrock 1.5 ratio rockers, Crane pushrods, Edelbrock Air Gap manifold, Rochester Q-Jet,Hedman Hedders, MSD Pro Billet distributor, MSD HVC coil, MSD Digital 6 ignition, MSD 8.5mm wires
|Transmission ||TH400, Trans-Go Shift Kit, B&M Torque Master 2400 converter |
| Rear ||Edelbrock adjustable upper control arms, Edelbrock boxed lower control arms |
|Differential ||GM 12-bolt, 3.73:1, with Powertrax No Slip |
|Wheels ||Custom, by Stockton Wheel |
| Front ||15x7, 4-inch back spacing |
| Rear ||15x10, 5 3/4-inch back spacing |
| Front ||95/60R15 BFG Comp T/A |
| Rear (street tires) ||275/60R15 BFG Comp T/A |
| Rear (race tires) ||275/60R15 BFG Comp T/A Drag Radials |
|drag strip times ||13.05 at 106.89 mph |
|“Before” || |
|fuel consumption ||13 mpg |
|Curb weight ||3,640 pounds without driver |
2244 W. McDowell
1131 Via Callejon
Additional Assistance From: BFGoodrich
P.O. Box 19001
7532 Anthony Ave.
B&M Racing & Performance Products
9142 Independence Ave.