Chevy Nova EFI Kit - Fuel Injection For Better HP And MPG

The morning commute in the general vicinity of New York City is a daily grind of traffic and construction, and can border on total mayhem at times. Needless to say, it's not enjoyable unless you can find a way to put all your worries behind you. What could be cooler than driving a vintage Chevrolet to and from work everyday? People stare, take pictures on the camera phone, throw you some thumbs up, and generally can't help but notice that you are obviously having a much better commute to work than they are.

The donor '70 Nova is an awesome shade of metallic mint green.

New Jersey resident and automotive technician Bob Twynam is living the good life. His commute to and from work is a Garden State norm of close to 80 miles. About a year back, a long-time repair shop customer of his reached the young age of 89 and decided to hang up the old key ring. Her pimp wagon, I mean, mode of transportation was a beautiful green-on-green '70 Chevrolet Nova with a 307 cubic-inch small-block and a bench seat. She sold him the car and he decided to turn it into his daily driver.

The body of the Nova is in beautiful condition. The black top is without damage, the body panels have yet to transform into Swiss cheese, the gauges still work--even the seats look like they have yet to be sat on. The only downside to the Nova is the powerplant. Without trying to offend anyone, let's just say that the 307 was not the most sought after motor from 1968 to 1974. Today, most of the 307's are long gone...and for good reason. Bob's 307 two-barrel was good enough for what he was using it for, but he wasn't entirely satisfied. "Who wouldn't want to drive a '70 Nova to work every day? The only problem is, if you don't warm it up for 10 minutes, it stalls, acceleration sucks, and it gets awful gas mileage," Bob says.

We threw it on the dyno at Tune Time Performance in Toms River, New Jersey, for some preliminary emissions and dyno testing.

We threw it on the dyno at Tune Time Performance in Toms River, New Jersey, for some preli

We thought this was the perfect test mule for Edelbrock's new Pro-Flo XT electronic fuel injection kit. The multi-port injection system upgrades the ignition, fuel, and intake system on the small-block Chevy into a state of the art gas-sipping monster.

With the XT calibration handheld tuning box, maximum tunability is simply a button press away and can be achieved from the driver's seat. Also, a laptop can be hooked-up to the Edelbrock ECU for even more tuning features, such as fuel maps, spark modifier tables, and air-fuel ratio graphing, just to name a few. The 90mm throttle body, equal length intake runners, and 29 psi Pico fuel injectors ensure both maximum performance and optimal efficiency.

Our base numbers were 174 corrected rwhp and 228 lb-ft of torque--surprisingly good, we think.

Our base numbers were 174 corrected rwhp and 228 lb-ft of torque--surprisingly good, we th

Given the present Great Depression and instability of fuel prices, there is no better time to be increasing productivity in your hot rod to achieve better fuel economy. We set some realistic goals, including a horsepower increase of 35, fuel economy increase of 5 mpg, seamless cold-weather startup, and a hydrocarbon parts-per-million drop off of 80 (exhaust gases). We installed the kit in a little over 12 hours (a hearty weekend) and given the plug-and-play nature of the components, most went on in a breeze. Follow along as we install Edelbrock's Pro-Flo XT electronic fuel injection kit.

Additional Parts Needed
To complete this install, there are a few pieces that are not included in the Edelbrock kit.
Intake gaskets
Silicone
Intake manifold bolts (8)
Thermostat housing
195-degree thermostat
Teflon tape
Low-resistance spark plug wires
Intake pipe and 4-inch filter
LS-style throttle cable (Lokar PNTC-1000LS1U)
Pull ties

Trick of the Trade: With the '68-72 Nova, you can prop up the hood to vertical by taking out the front hood bolt on each side, loosening the back and pushing it back. This makes life so much easier when working under the hood. The only other option is taking the hood completely off when installing a kit such as this.
Trick of the Trade: With the '68-72 Nova, you can prop up the hood to vertical by taking o
Next came the intake manifold. After disconnecting all the wires, throttle linkage, radiator hose, and distributor, the eight intake bolts can be removed. Most manifolds require some persuasion as the silicon creates a tight bond. A quick wedge with a flat-head screwdriver and out she comes.
Next came the intake manifold. After disconnecting all the wires, throttle linkage, radiat
The intake surface must be cleaned and prepared to ensure a good seal with the new intake manifold. At this point, we let the 5-point-slow loser of the bunch jump in and do the dirty work.
The intake surface must be cleaned and prepared to ensure a good seal with the new intake

After a bead of silicone across the front and back of the block where it meets the manifold, and a set of Fel-Pro intake gaskets from the local parts store, the intake was set in place. Make sure all the bolt holes line up and begin installing them. We replaced the original rusted intake manifold bolts with new ones to ensure the "new" look.
After a bead of silicone across the front and back of the block where it meets the manifol
Next, we dropped in the new Mallory electronic distributor, as this would be difficult to do after the wires are hooked up and in the way. We also wanted to make sure that we had enough clearance between the firewall and the rear of the intake. It fit like a glove.
Next, we dropped in the new Mallory electronic distributor, as this would be difficult to
Now is the perfect time to organize all the wires. Using the very helpful directions that come with the kit (also available at www.edelbrock.com), we maneuvered the wires into their approximate location upon completion.
Now is the perfect time to organize all the wires. Using the very helpful directions that

This also helped when we attached the new coil to the firewall using sheetmetal screws. You don't want tension in the electrical lines, but also don't want to be wading through wires.
This also helped when we attached the new coil to the firewall using sheetmetal screws. Yo
Trick of the Trade #2: While installing the new thermostat, we drilled a hole through the base ensuring that air does not get trapped in the manifold, leading to a problem with circulation. The hole ensures that the manifold is filled with water at all times. We cleaned and painted the thermostat housing off the original manifold and reused it.
Trick of the Trade #2: While installing the new thermostat, we drilled a hole through the
Next, we mated the engine bay wiring harness with the cockpit wiring harness. The instructions ask that you drill a 1 1/2-inch hole in the firewall to do so. We tapped into a previously made hole that was once used for an air conditioning system.
Next, we mated the engine bay wiring harness with the cockpit wiring harness. The instruct

We then made and ran the fuel line and return. The kit comes with 20-feet of flexible fuel hose as well as all the ends and instructions on how to attach them. You can either create a new return line to the tank or reuse the original fuel supply line as the return. We decided to make a new line and ultimately had to order ten more feet of line to finish the job.
We then made and ran the fuel line and return. The kit comes with 20-feet of flexible fuel
The O2 sensor needs to read the oxygen content in the exhaust system and thus must be mounted on the exhaust pipe. The hole was drilled, and the bung was welding into place.
The O2 sensor needs to read the oxygen content in the exhaust system and thus must be moun
Photographers note: Use a long lens and stand a few hundred feet away. Sparks do sting.

We had to drop the tank and install the new fuel hose. We simply attached a 6-inch piece of hose to a fitting and bolted it to the mount. No filter was needed as we will add an inline fuel filter after the fuel pump.
We had to drop the tank and install the new fuel hose. We simply attached a 6-inch piece o
We mounted the fuel pump and fuel filter to the inner framerail, clear from danger of the tire, shock, and leaf spring.
We mounted the fuel pump and fuel filter to the inner framerail, clear from danger of the
The in, return, and wiring for the fuel pump was all run together down the length of the car and pull-tied together every six inches. This ensures that they don't move and scrape on anything. Any contact could cause a catastrophe. We made sure we had plenty of clearance between the lines and e-brake wire.
The in, return, and wiring for the fuel pump was all run together down the length of the c

In the interior of the car, we used double-stick tape supplied with the kit to mount the ECU. Also, we attached the wiring components to it and made sure to sneak them up behind the dash and out of sight. Then, a wire was run from the wiring harness to a switched 12-volt source to give the ECU power, but only when the key was turned on.
In the interior of the car, we used double-stick tape supplied with the kit to mount the E
Check out Matt Haufffe of Tune Time Performance using the XT Calibration Module that comes with the kit. The base program must be installed as per application with the tuning CD provided with the kit. Here, Matt was tuning the fuel map on the dyno for optimal performance. The XT provides an assortment of tuning tools, including fuel and spark maps, digital diagnostic readouts, and idle adjustments, among others.
Check out Matt Haufffe of Tune Time Performance using the XT Calibration Module that comes
The finished product. The instructions made installation very easy. All the wires have unique ends on them, which eliminates the chance of hooking them up wrong. Ford-boy gave us an elbow to use and we picked up a cone-style filter from AirAid to button it up.
The finished product. The instructions made installation very easy. All the wires have uni

After all was said and done, we hit Tune Time Performance again to get some final numbers.
We made 210 hp and 267 lb-ft of torque, an increase of 36 hp and 39 lb-ft, thus matching our goals. We increased fuel economy from 13.8 to 18.9 mpg, an increase of 5.1, and a savings of over $700 a year based on how the car is currently used. Hydrocarbon content dropped from 160 to 118, making the 307 far more emissions friendly. Throttle response is now instantaneous.
We made 210 hp and 267 lb-ft of torque, an increase of 36 hp and 39 lb-ft, thus matching o
Last, but certainly not least, a few cranks of the starter and you are ready to rock. No stumbles, stalls, or other problems.
Last, but certainly not least, a few cranks of the starter and you are ready to rock. No s

SOURCES
Edelbrock Corporation 2700 California St. Torrance CA 90503 310-782-2222 www.edelbrock.com	Airaid Filter Company www.airaid.com
TuneTime Performance