Back in part 7 of Modern Mouse, not only did we add boost to our LM7 test mule (now displacing 383 ci), but we threw in a single turbo test on a stock 5.3L LS as well. We also promised (and delivered) testing on an LS3-based stroker combination from Texas Speed and Performance entitled Monster Mouse (October 2012 issue).
Though we’ve started our dalliance with Monster Mouse, Modern Mouse is still alive and well. Loyal readers will remember that Modern Mouse started out life as a simple 5.3L LM7 pulled from a wrecking yard. The iron-block 5.3L was subjected to all manner of upgrades before tearing it down to bump the displacement to 383 ci. The hike in displacement came from a forged rotating assembly that included a 4.00-inch stroke forged crank and matching rods from Procomp Electronics, combined with forged pistons from Probe Racing. Though a variety of different heads have been run on Modern Mouse, it was sporting a new set of CNC-ported heads from Procomp Electronics for this test. Given the ported heads, healthy Comp cam and CNC-ported heads, the 383 was primed and ready for the new LS Perimeter Plate nitrous system from Zex.
Designed specifically for LS applications, the Perimeter Plate Blackout system featured a unique intermediate plate designed to sandwich between the throttle body and intake manifold. It was designed as a direct fit for all 90mm (factory) and larger aftermarket manifolds, including the FAST LSXR and LSXRT. A machined O-ringed insert was used to step down the 102mm opening to fit the smaller 90mm throttle bodies and intakes.
What every LS owner should be hiding behind their throttle body!
1 You will remember that our 5.3L LM7 was upgraded with a forged stroker assembly includi
2 Forged flat-top pistons were supplied by JE Pistons.
According to Zex, the Perimeter Plate system offeres a number of other design features including perimeter injection, Cryo-Sync, and airflow enhancement technology. The Perimeter Injection employed 12 injection points that combined nitrous and fuel to optimize atomization and distribution in the manifold. Flowing super cool nitrous (-127 degrees) through the plate effectively turned it into a Cryo-Sync (or heat isolator) to help cool the intake and throttle body. Flow of the nitrous and fuel through the spacer plate and into the manifold also created a low-pressure zone to further enhance airflow into the motor. On paper, the Perimeter Plate sounded pretty effective, so we installed one on Modern Mouse.
Using jetting to control the nitrous and fuel flow, the Zex system was adjustable from 100 hp to 250. For Modern Mouse, we chose to run the system at 100 hp, then again at 150 hp, both reasonable for street use when adhering to the recommended timing retard for each power shot. According to Zex, the timing should be retarded by four degrees for the 100hp shot and six degrees for the 150hp shot. While our LM7 was now sporting a manual throttle body (102mm from FAST), the Zex Perimeter Plate system was also designed to run on drive-by-wire applications. Using a sophisticated controller, the system will self-learn, and only activate at wide-open throttle. This was an important safety feature, as you never want to activate a nitrous system at low engine speeds or part throttle. Hooking up the system according to the instructions was straightforward, and Zex was kind enough to supply a bottle heater to ensure optimum bottle pressure (over 900 psi).
Before running the new nitrous system, we had to establish a baseline. The 383 stroker was equipped with a Comp 281LRHR14 cam offering a 0.617/0.624 lift split, a 231/239 duration split and 113-degree LSA. The forged short block featured Fel Pro head gaskets and ARP head studs to secure the CNC-ported LS1 heads from Procomp Electronics. Stock rockers were used with 7.300-inch length hardened pushrods from Comp Cams. The induction system consisted of a FAST LSXRT intake, 75-pound injectors, and XFI management system.
3 Keeping things sealed was a set of rings from Total Seal. These were important to Moder
4 For this test, we chose a streetable but powerful cam grind (281LRHR14) from Comp Cams
5 Another change made for this test was installing a set of CNC-ported heads from Procomp
Feeding the thirsty injectors was an Aeromotive A1000 fuel pump, 13110 Pro-Series EFI regulator, and 12301 fuel filter. A quality fuel system on a high-horsepower nitrous motor is a must. The motor was run in anger to the tune of 544 hp at 5,900 rpm, and 514 lb-ft of torque at 4,800 rpm. Torque production exceeded 480 lb-ft from 4,000 rpm to 5,900 rpm. Obviously the long-runner LSXRT intake, 281LR cam, and CNC-ported heads were all working well together. Even down at 3,000 rpm, the 383 stroker produced over 450 lb-ft of torque. Such is the benefit of the additional displacement compared to a typical 5.3L. Now it was time to hit the nitrous.
Preparation of the nitrous test included installation of the proper fuel and nitrous jetting (28/52), retarding the timing by four degrees using the XFI management system and heating the bottle until the internal pressure registered 900 psi. Once everything was set, we dropped the hammer once again, then engaged the nitrous. The motor got real happy, and power jumped to 660 hp and 655 lb-ft of torque. The 100hp shot increased power output by 116 hp and 141 lb-ft of torque.
Since the system is adjustable, we decided another shot was in order and stepped up to 150hp jetting (32/64). The timing was retarded another two degrees (total of six) as we once again engaged the nitrous at wide-open throttle. As before, the Zex Perimeter Plate system offered impressive power gains, jumping peak power to 706 hp at 5,700 rpm, and 737 lb-ft of torque at 4,700 rpm. Thanks to the Perimeter Plate system from Zex, Modern Mouse was pumping out some serious power, capable of pushing a fourth-gen Camaro or LS-swap muscle car easily into the 10s, and perhaps even into the 9s.
6 The exhaust ports were given the CNC treatment as well. Note this included modification
7 The dedicated castings feature 2.055/1.60 stainless steel valves and CNC-profiled 64cc
8 Naturally the heads received something other than factory valve springs. The dual-sprin
NA vs Zex Perimeter Plate (100hp Shot)
How do you not marvel at the power gains offered by nitrous oxide? Is it any wonder so many racers use the stuff? Just push a button and you are instantly rewarded with massive power gains. Who couldn't use an extra 100 hp in their street car? Sporting the CNC heads from Procomp Electronics, a Comp cam and LSXRT intake, Monster Mouse pumped out 544 hp and 514 lb-ft of torque. After installation of the Zex Perimeter Plate system, the peak power numbers jumped to 660 hp and 655 lb-ft of torque. These power gains were achieved using 100hp jetting. It is important to note that the Zex nitrous system was designed to run at the factory fuel pressure (58 psi). More pressure will richen up the mixture while less will lean things out. Our Aeromotive fuel system included an adjustable fuel pressure regulator that allowed us to dial in the desired fuel pressure.
NA vs Zex Perimeter Plate (150hp Shot)
As happy as we were with the results of the first test, the adjustability of the system was just too tempting. Stepping up from the 100hp jetting to the 150hp shot, we once again applied the Zex Perimeter Plate system to Modern Mouse. The little stroker that could responded with even more power, jumping to 706 hp and 737 lb-ft of torque.
9 To mix things up a bit, we chose the LSXRT intake over the LSXR version. The intake was
10 Aeromotive supplied an A1000 fuel pump along with an adjustable fuel pressure regulato
11 To establish a baseline for the nitrous test, we ran the combination in normally aspir
12 After running the motor in normally aspirated trim, we installed the Zex Perimeter Pla
13 The plate was labeled for proper orientation. The last thing you want is to have the n
14 The Perimeter Plate system utilized jetting to adjust the power output. We chose 100hp
15 We chose to mount the fuel and nitrous solenoids on the intake. Note the black braided
16 Run in anger with 100hp jetting, the Zex Perimeter Plate system increased the power ou
7805 Barton Street
15312 Connector Lane
3406 Democrat Road
605 S. Milliken Avenue