Super Chevy
Click here to find out more!

Chevy Mark V Big Block Engine Build Up - Power-Packed Mark V

This 540 CID Chevy Big Block Is Built to Rock

Photography by Cam Benty

CamQuest 6 Asks - Can We Do Better?Our 540-cid Chevy big-block Mark V engine was a standout performer. It did everything we asked it to do. But did we optimize the performance? Did we get everything we could from the combination? Knowing that we were up for anything the learning curve might throw our way, we decided to test our camshaft knowledge against the newest programming available from COMP Cams-the CamQuest 6 Cam Selection Software.

As touted in the ad materials, the CamQuest 6 is a PC-based camshaft selection program that allows the user to find the right camshaft by answering a few application-specific question from the program's dropdown menus. Sounds simple enough, so we took the program for a testdrive.

First, we input the parameters required by the program, such as engine type, compression, carburetion, cylinder head type, etc. The program offers up an amazing number of possibilities. For our Mark V big-block engine, the program was easy to understand and required little intuitive thinking on our part to fill in the grids accordingly. Our only "gray" area occurred with regard to the flow figures of our ported RHS Pro Action 360cc cylinder heads. Having the exact measurements here would give us more accurate information in terms of the total calculation, but we were comfortable in running the simulation with the data we had in hand. The CamQuest 6 calculated the data and kicked out a number of good, better, and best camshaft choices. Interestingly enough, our model RA306-10, (0680-inch lift and 306/319-degrees duration, 110-degree lobe centers), the one that generated the 649 hp on the Westech dyno, was not the top CamQuest 6 camshaft selection. So what did the CamQuest 6 recommend? Camshaft (grind number RA296ER-8) with less duration and more lift on 108-degree lobe centers.

To determine how much better the smaller duration camshaft would be, we did two virtual installs using CamQuest 6. As it was the top pick, the program used grind RA296ER-8 and displayed the results, along with all of the recommended ancillary COMP Cams parts like lifters, retainers, springs, locks, and other parts that should be used to achieve optimum performance. Grind RA296ER-8 (the top CamQuest 6 camshaft selection) features 108-degree lobe centers, with only 296-degree intake duration (304-degree exhaust). Lift was increased to 0.714 inches. Our new estimated horsepower-nearly 689 hp. Torque-655. So why the 30hp difference? We decided to investigate.

According to Westech's Steve Brule, the camshaft chosen for the dyno test featured a large amount of duration-too much for the application due to the engine's limited compression. With a pump gas-compatible engine such as this, the increased duration actually allows cylinder pressure to be reduced, slightly lowering peak power.

"This type of engine (540-cid Mark V) can handle a lot of lift, but too much duration is a detriment," says Brule. "The excessive duration, however slight, actually bleeds off intake charge. It negatively affects the volumetric efficiency and increases the exhaust gas temperatures. But the higher lift is not a problem; in fact, it gets the valve moving slightly quicker, helping fill the cylinder more fully making more power. As long as you don't have valve to piston problems, lift is only a positive thing."

The camshaft selection process has long been a black art by both pro and novice engine builders, leaving lots of room for interpretation. How do you know you have purchased exactly the right camshaft for your engine? In the past there has been only one way-to trust in the expertise of those who are believed to be experts. Today, real experts are easy to find, such as those answering the phone at the COMP Cams Cam Help hotline. Unfortunately, many builders don't make the call and rely on their friends and pseudo experts to advise them. With engine building requiring not only cubic inches, but also cubic dollars to build big power, it's safe to believe there are now two very reliable sources for camshaft advice-Cam Help and CamQuest 6.

SOURCES
Westech Performance Group
11098 Venture Dr., Unit C
Mira Loma
CA  91752
9-09/-685-4767
www.westechperformance.com
Eagle Specialty Products
Southaven
MS
6-62/-796-7373
eaglerod.com
Barry Grant
Dahlonega
GA
706-864-8544
www.barrygrant.com
COMP Cams
Keith Black Pistons
7-75/-882-7790
kb-silvolite.com
Milodon
2250 Agate Ct.
Simi Valley
CA  93065
805-577-5950
www.milodon.net
Adams Metalizing & Grinding Engine Machinework
Dept. SC
Lancaster
CA  93534
Jim Shewbert Power Systems
Dept. SC
Palmdale
CA  93551
RHS - Racing Head Service
Dept. SC
Memphis
TN  38118
Scat Crankshafts
3-10/-370-5501
www.scatcrankshafts.com
Enjoyed this Post? Subscribe to our RSS Feed, or use your favorite social media to recommend us to friends and colleagues!
Super Chevy