Spread the news:
Joel Rosen is back.
Rosen, the man behind the legendary Baldwin-Motion SS and Phase III big-block Camaros, Novas, Chevelles, Biscayne Street Racer Specials, and Corvette Supercars of the '60s and '70s, has returned with a 21st Century version of the mind-blowing cars that roared out of his shop in Baldwin, Long Island, New York, and terrorized the streets not only in the U.S., but around the world.
He's once again joined by Marty Schorr, who was part of the original Motion Performance group that turned out those legendary "take no prisoners" ground-pounding musclecars. Rosen and Schorr have linked up with a new Motion Team consisting of Joel B. Ehrenpreis and Larry Jaworske.
Together, they're launching a new, limited-production, 12-car build, two-seat '69 Baldwin-Motion 540 Camaro SuperCoupe designed by Kris Horton and powered by a Kinsler-injected, 540ci Merlin/Motion engine. Cranking out over 700 hp, the Merlin/Motion 540 is set back 13 inches on a full tubular chassis for a true front/mid layout. You could call it the "great American supercar."
Billy Mitchell chose the Eagle lightweight 4350 chromoly steel crankshaft for durability a
Since the crank is internally balanced, the rear flange is counterbalanced for bottom end
The main journal oil-feed holes in the Eagle crank are cross-drilled to increase oil flow
Billy Mitchell, who built engines for Rosen 35 years ago, was commissioned by the new Motion team to assemble the prototype engine. "Since I built many of the original Baldwin-Motion cars and built and drove the NHRA-record-setting A/MP Motion Supercar Club Camaro," Mitchell says, " I knew exactly what the new car needed... a Motion-spec, 700-plus-hp, all-aluminum 540-inch Merlin big-block."
Rosen and Mitchell teamed up to design the engine to Rosen's specifications. Mitchell began by blueprinting and balancing the engine. The Merlin III heads received a COMP Cams roller valvetrain with a flat tappet camshaft for the initial build. This "Phase I" engine was built with a single 1050 four-barrel with 82/82 jetting on a Merlin X manifold that delivered 630 hp at 5,800 rpm, and 630 lb-ft of torque at 4,400 rpm on the dyno.
Mitchell removed the 4-bbl carb and intake, sealed the engine, and shipped it to Keech's Performance (part of the Motion team) in Sarasota, Florida. From there, the engine went into "Phase II" assembly. Steve Keech picked up where Mitchell left off, and was responsible for completing the engine and installing it in the prototype Baldwin-Motion 540 Camaro SuperCoupe.
The Eagle ESP H-beam connecting rods measure 6.535 inches and weigh approximately 785 gram
A connecting rod's weakest link is always the bolt. Mitchell chose ARP L19-forged rod bolt
The 10.0:1 compression Mahle small dome forged-aluminum alloy pistons are lightweight and
A second set of Mitchell-prepared heads was shipped, and these were sent out for polishing. When they returned, they received the COMP Cams roller valvetrain. A roller camshaft, with a custom Motion grind designed by Rosen, was slipped into the block.
The crowning jewel atop the Merlin/Motion's 540 engine is the exotic Kinsler Cross Ram injection system. Rosen worked with Jim Kinsler on the overall specs to produce a precise, computer-controlled sequential electronic fuel injection system to accurately feed the 700-plus-hp the Merlin/Motion engine now produces.
The Merlin/Motion 540 is the first in a succession of engines that can be tailored to the customer's power preferences. Motion can build an engine capable of producing 1,000 hp, if the buyer wishes, for their Baldwin-Motion 540 Camaro SuperCoupe. Since only 12 will be built, however, buyers best be quick to belly up to the bar and order one. Just like the old days at Baldwin Motion, Joel Rosen and the new Motion team's 21st Century Baldwin-Motion 540 Camaro SuperCoupe, with its Merlin/Motion engine, are building the great American supercar again.
World Products' Merlin aluminum block has a 4.50-inch bore, 4.25-inch stroke and 4.840-inc
Each Merlin/Motion block is numbered to match the Camaro SuperCoupe's production number. T
Fel Pro's pre-flattened steel wire ring head gasket has a compressed thickness of 0.041 in