Material: A356-T61 aluminumCombustion Chamber Volume: 64cc or 72ccIntake Port Volume: 195ccIntake Port Dimensions: 2.07 inches high x 1.26 inches wideExhaust Port Volume: 75ccExhaust Port Dimensions: 1.35 inches high x 1.50 inches wideValve Type: CNC-profiled, one piece, non-magnetic stainless steel with hardened tipsIntake Valve: 2.02-inch head diameter, 11/32-inch stem diameter, 4.96-inch OALExhaust Valve: 1.6-inch head diameter, 11/32-inch stem diameter, 4.980-inch OALValve Guides: Bronze alloy, .500-inch O.D.Seals: VitonValve Seats: Tungsten alloy, compatible with unleaded fuelsValve Springs:1.260-inch springs1.260-inch O.D. single with damper110 lb at 1.700 inches installed height290 lb at 1.200 inches360 lb per inch spring rate.520 inch max valve lift 1.470-inch springs1.470-inch O.D. single with damper120 lb at 1.780 iches. installed height300 lb at 1.280 inches360 lb per inch spring rate.540 inch max valve lift 1.460-inch springs1.460-inch O.D. double with damper125 lb at 1.780 inches installed height376 lb at 1.180 inches420 lb per inch spring rate.600 inch max valve lift Valve Locks: 7 degree stamped steel on all 1.25-inch springs, 7 degree + .050 inch machined steel on all other spring versionsValve Retainers: Chrome-moly steelMax rpm: 6,500Rocker Studs: ARP 3/8 inch included with all headsGuideplates: For use with 5/16-inch hardened pushrods, included with all headsOEM Accessory Holes: Yes Note: The use of a valvetrain combination that exceeds the maximum valve lift will void the warranty. Piston-to-valve clearance must be checked in all cases. Recommended Components for 23-Degree HeadsHead Gasket: Fel-Pro 7733PT-2 for mild engines up to 4.060-inch boreFel-Pro 1010 for high output engines up to 4.155-inch bore (will not indent aluminum heads)Fel-Pro 1014 with pre-drilled steam holes for 400 engines (must modify heads)Intake Gasket: Fel-Pro 1205Exhaust Gasket: Fel-Pro 1404Head Gasket Kits: TFS-30400905 for mild engines up to 4.060-inch bore (pre-1987 only)Head Bolts: ARP-134-3601 (6 pt.) or ARP-134-3701 (12pt.)Head Studs: ARP-134-4001 (6 pt.) or ARP-234-4301 (12 pt.)Moly Lube: ARP-100-9902RTV sealer: Permatex Ultra Black #598BRThread sealer: Permatex Aviation Form-A-Gasket #3HThread locker: Loctite Blue #242 for medium strength applications or Loctite Red #272 for high-strength Roller Rocker Arms: Crane Gold Race 1.5 ratio 11750-16 or 1.6 ratio 11759-16Trick Flow 1.5 ratio TFS-31400510 or 1.6 ratio TFS-31400511Summit 1.5 ratio SUM-G6910 or 1.6 ratio SUM-G6920 Note: All rockers fit 3/8-inch studs.If you use other brand rockers, you must check them for operating clearances and proper geometry. Stamped steel rockers should be used only with stock or very mild cams. « | 1 | 2 | 3 | » | View Full Article Enjoyed this Post? Subscribe to our RSS Feed, or use your favorite social media to recommend us to friends and colleagues!