Super Chevy
Click here to find out more!

Brodix LS7 Cylinder Heads - Big Bro

Testing the new Brodix LS7 cylinder heads

By Richard Holdener, Photography by The Author

The problem is that there are diminishing returns when it comes to improving flow. What Brodix did with its STS BR7 273 head was start with a smaller, more efficient port than the factory LS7 head. By doing so, it was able to come up with an LS7 head that offered not only over 400 cfm at 0.700 lift, but did so without resorting to excessive port volume. In fact, according to its literature, the new STS BR7 273 heads flow 416 cfm at 0.700 lift through an intake port that measured just 273cc (roughly equivalent to a stock LS7). What this means is that even a stock LS7 can take advantage of the extra airflow offered without concern for lazy, oversized ports that might hurt drivability and low-speed performance.

The Brodix STS BR7 273 heads offered a number of desirable features, including oversized valves, a 12-degree valve angle and full LS7 compatibility. The Brodix LS7 heads combined full CNC porting with a 2.25/1.614-inch valve package and 71cc combustion chambers to maximize head flow through the 273-cc intake port. With a peak advertised intake flow of 416 cfm at 0.700 lift (240 cfm for exhaust), these Brodix heads offered big-block flow through significantly smaller ports. This is important when running these heads on (relatively) small-displacement motors.

Part of the credit for the impressive flow numbers goes to the 50-degree valve job on the intake (45-degree on exhaust). This represented an increase of roughly 80 cfm over the stock LS7 heads. Additional beneficial features included a standard LS7 exhaust pattern, valve centerline and intake flange. Naturally the Brodix heads also accepted the factory (or aftermarket) 1.8-ratio rockers. The Brodix LS7-based heads were recommended for LS applications sporting a minimum bore size of 4.125-inches. The valve size, placement and chamber size necessitate the large bore diameter.

The Brodix heads looked good on paper, but just how would all the specifications translate into power? To properly test the big Bros, we needed a suitable test motor that offered a minimum bore size of 4.125 inches. What we had was something even bigger, capable of utilizing every last cfm offered by the STS BR7 273 heads.

The big-inch stroker small block started out life with a new aluminum block from RHS. Looking to maximize displacement, we stepped up to tall-deck block, which offered the capability to swallow a massive 4.5-inch stroke with plenty of deck height to spare for acceptable rod ratios. The A357-TR RHS aluminum block was a serious piece of hardware and offered an impressive list of features including Clean-Cast technology, priority main oiling system and billet main caps with ARP studs. Filling the stroker-friendly RHS block were equally stout components from Lunati, Wiseco and K1. Lunati supplied a massive 4.5-inch billet stroker crank, which was combined with a set of 6.30-inch forged K1 rods and 4.185-inch Wiseco forged, flat-top pistons. The bore and stroke combined to produce a displacement of 495 ci, easily surpassing the '70 454 LS7 big-block.

The cubes combined with flat-top pistons and 71cc combustion chambers to produce a static compression ratio of 13.5:1. Sealing the big beast was a set of Cometic MLS head gaskets secured by ARP heads studs. Additional components employed on the RHS stroker included a Moroso pan, pick up and windage tray, an adjustable timing chain designed specifically for the tall-deck block (1 extra link per side) and a custom hydraulic roller cam from Crane Cams. Big for a hydraulic roller LS application, the powerful Crane cam featured 0.661 lift, a 260/276-degree duration split and a 114-degree lobe separation angle.

The 0.661 lift came courtesy of the 1.8 rockers employed on the LS7 heads. Were this cam run in an LS1 or LS3, the lift would reduce to 0.624 thanks to the smaller 1.7-ratio rockers. Crane Cams also supplied a set of link-bar hydraulic roller lifters and hardened pushrods for the test.

Feeding the beast was a Mast Motorsports (high rise) single-plane intake designed to accept the Holley 1050 Ultra Dominator carb. Ensuring adequate fuel to the stroker was a complete Aeromotive fuel system, including an A1000 fuel pump, regulator and filter.

To properly test the Brodix heads, we first needed to establish a baseline with the LS7 stroker with stock style heads. Test number 1 involved the installation of a set of as-cast LS7 LSX (ports cast to duplicate production LS7 CNC heads) heads. The heads were upgraded with a suitable valve package from Brian Tooley Racing to accept the rpm capability and 0.661-lift cam. Both heads were run with the same 1 7/8-inch headers, though given the displacement and power potential, this stroker combination would likely respond to a set of 2.0-inch (or larger) headers. After jetting and timing, the 495 stroker produced peak numbers of 744 hp at 6,300 rpm and 682 lb-ft of torque at 4,700 rpm.

After swapping over to the Brodix STS BR7 273 heads, the peak numbers jumped to 799 hp at 6,500 rpm and 714 lb-ft at 5,300 rpm. The Brodix heads never lost out to the stock LS7 heads, offering significantly more power and torque from 4,000 rpm past 6,500 rpm. Torque production with the Brodix heads exceeded 700 lb-ft from 4,400rpm to 5,800 rpm. Obviously the big flow and small port volume worked well on this big-inch application.

SOURCES
Brodix
301 Maple P.O. Box 1347
Mena
AR  71953
479-394-1075
www.brodix.com
Mast Motorsports
330 NW Stalling Drive
Nagodoches
TX  75964
866-551-4916
http://www.mastmotorsports.com
Cometic Gaskets
8090 Auburn Road
Concord
OH  44077
800-752-9850
www.cometic.com
MSD
915-857-3344
www.MSDIgnition.com
Holley/Hooker
1801 Russellville Road
Bowling Green
KY  42101
270-782-2900
www.holley.com
K1 Technologies
Byron Center
MI
www.k1technologies.com
RHS
3416 Democrat Road
Memphis
TN  38118
877-776-4323
www.racingheadservice.com
Wiseco Pistons Inc.
7201 Industrial Park Blvd.
Mentor
OH  44060
Aeromotive
7805 Barton Street
Lenexa
KS  66214
913-647-7300
http://www.aeromotiveinc.com
Crane Cams, Inc.
530 Fentress Blvd.
Daytona Beach
FL  32114
904-258-6174
www.cranecams.com
By Richard Holdener
Enjoyed this Post? Subscribe to our RSS Feed, or use your favorite social media to recommend us to friends and colleagues!
Super Chevy