Nova Steering & Suspension Upgrade - Tech Information

Nova Suspension Steering 1971 Chevrolet Nova

It's a well-known fact that there's room for a great deal of improvement when it comes to the handling characteristics of early musclecars. With this in mind, and with a big-block Nova that sincerely needed help in the handling department, we thought we'd take advantage of the components and technology available these days and perform a few bolt-in mods to correct those deficiencies.

To this end, we approached a few of the leaders in the suspension and steering industry (namely Fatman Fabrications, QA1, Classic Performance Products, Wilwood, and Hellwig Products) and procured the components needed for the upgrade. The '71 Nova was originally a six-cylinder car that had been outfitted with a 396-cube big-block and a TH400 trans. The original suspension, though, was not upgraded along with the engine, adding insult to injury in the handling department.

To improve the less-than-satisfactory handling characteristics of this nose-heavy hauler, it was imperative that we start with coil springs of the correct rate. Along with a pair of CPP springs, we also installed a set of Fatman tubular control arms and G-Force spindles, a Hellwig sway bar (provided by Fatman Fab), a set of QA1 fully adjustable shocks, a CPP quick-ratio steering box assembly, and Wilwood Dynalite Pro disc brakes-confident that this combination of components would go a long way in improving the handling, ride, and stopping power of this muscular Nova. See how uncomplicated the installation of these aforementioned components was, and keep in mind, we'll be back with a few rear suspension upgrades as well before our final track testing, so stay tuned.

The subject Nova came to us sporting a big-block in place of its original six. The suspension was unmodified though it had at one point received an OEM-style disc brake conversion-an improvement over the factory drums but absolutely no benefit handling-wise.
The subject Nova came to us sporting a big-block in place of its original six. The suspens
The upgrade was started by removing the calipers, the rotors, and disconnecting the steering arms from the stock spindles.
The upgrade was started by removing the calipers, the rotors, and disconnecting the steeri
After we placed a floor jack under the lower control arms and broke loose of the spindle nuts, we lowered the jack, releasing the pressure on the springs and then slid them out of their pockets.
After we placed a floor jack under the lower control arms and broke loose of the spindle n

With the springs out of the way, it was quick work to unbolt and remove the stock upper and lower control arms.
With the springs out of the way, it was quick work to unbolt and remove the stock upper an
The following images show the differences between the stock stamped-steel control arms...
...and the much lighter performance aftermarket arms provided by Fatman Fabrications.

The Fatman spindles bolt easily into place with no modification and are extremely strong. They're fabricated from SAE 1010-grade material and are 1-inch-diameter and 0.188 wall thickness. They also come with a unique urethane spring seats or can be used with coilover shocks and/or Air Ride components.
The Fatman spindles bolt easily into place with no modification and are extremely strong.
Perhaps the most noteworthy components used in the upgrade (handling-wise) are Fatman's G-Force spindles. They not only provide a 2-inch drop for a lower center of gravity, but they also have the upper ball joint raised 2 inches to improve camber, and thus result in better traction and handling.
Perhaps the most noteworthy components used in the upgrade (handling-wise) are Fatman's G-
To help support the added heft of the big-block over the diminutive original six-cylinder engine, a pair of CPP coil springs were used in place of the overworked originals.
To help support the added heft of the big-block over the diminutive original six-cylinder

The next step was to install the new spindles. G-Force spindles will accept any disc brake system including the Dynalite Pro Series brakes we chose to use in our upgrade.
The next step was to install the new spindles. G-Force spindles will accept any disc brake
Here's a shot of the shocks chosen for the handling upgrade. QA1 aluminum-bodied adjustables have consistently proven themselves in numerous suspension upgrades we've performed over the years, so we naturally chose to use them again in this case.
Here's a shot of the shocks chosen for the handling upgrade. QA1 aluminum-bodied adjustabl
One other thing that was immediately apparent upon our initial testing was that the Nova's OEM steering box was well-worn. The steering was loose and there was a lot of play in the wheel. So, while we were doing the suspension upgrade it only made sense to also replace the ailing gear with a quick-ratio replacement from CCP.
One other thing that was immediately apparent upon our initial testing was that the Nova's

The CCP box is a direct bolt-in replacement, so it was an easy task to swap out. While we were at it we replaced the rag joint, too.
The CCP box is a direct bolt-in replacement, so it was an easy task to swap out. While we
To go along with the front suspension upgrade, Fatman supplied us with a new Hellwig heavy-duty anti-rollbar assembly, as well. The bar will greatly improve cornering by limiting body roll and the adverse effects it has on handling.
To go along with the front suspension upgrade, Fatman supplied us with a new Hellwig heavy
Once the suspension components were in place, we then turned our sights to the brake system. As the Nova sports a set of traditional 15-inch Cragar SS wheels, we couldn't go to large-diameter brakes. We did, however, find that Wilwood offered a great performance brake package that fit the bill perfectly-the Dynalite Pro Series. We started out by replacing the OEM master cylinder with a Wilwood unit designed to work with the calipers (mismatching calipers and master cylinders is a common problem that'll cause poor braking).
Once the suspension components were in place, we then turned our sights to the brake syste