Tri-Five Straight Axle Clip - Gasser Conversion Kit

Tri Five Chevy Straight Axle Clip Installation

Here at Super Chevy magazine we have received numerous e-mails from readers asking how to build a straight-axle Tri-Five. It seems that over the past decade or so, the nostalgic gasser look of the '60s has returned with a vengeance.

We won't bother going into the history of gassers in this article. Suffice it to say the gasser look and stance was all about weight transfer at the track. We put out the call for anyone doing a straight-axle install, and a year or so later found ourselves heading up to Clearfield, Utah.

The guys at Salt City Speed Shop (SCSS) answered the call and let us stand over their shoulders as we documented them installing a Jim Meyer Racing straight-axle conversion kit.

The crew at SCSS was in the middle of setting up a new shop location, so we moved the installation of the front clip to a more familiar setting-the family home garage. To tell you the truth, during the course of the install we kept expecting things not to fit quite right or run into some sort of problem. It never happened. On several occasions, SCSS's Kris and Larry Elmer commented on how well-engineered the Jim Meyer clip was. The '55 Chevy rolled into the shop, and five days later it rolled out of the shop, complete and ready. Due to the length of this install article we are going to jump right into the specifics.

What you see is what you get. The rear-steer leaf-spring suspension includes everything you'll need to install it into a stock 115-inch wheelbase Tri-Five frame. The straight axle assembly is complete with tube axle (any width), leaf springs (rated at 3,500 pounds for the pair) with front shackles and rear-frame brackets, shocks with frame-mount brackets, new Super Bell early Ford spindles with bolt-on Super Bell 2-inch dropped steering arms, new cross-steer Vega steering box with 2-inch dropped Pitman arm and cross-steer drag link and tie-rod. It features Wilwood 4-piston calipers with 10 3/4-inch rotors with a 5-on-4 3/4 wheel-bolt pattern to fit inside nostalgic 15-inch wheels. Included are box tube grafting sections to install the new suspension to the stock chassis that will be cut at the first body mount, just in front of the firewall. Also in this subframe kit are steering linkage hook-up kits or new ididit steering columns and disc/drum brake kits that plumb into your existing brake system.

The first obvious steps were to start dismantling the entire front end of the vehicle. During the dismantling process, the guys at Salt City Speed Shop tagged and bagged every nut, bolt, and wire. It helped prevent migraine headaches during the reassembly.
The first obvious steps were to start dismantling the entire front end of the vehicle. Dur
Larry Elmer, Kris's father, sparked up the blowtorch to cut loose some rusted and stubborn bumper bracket bolts. Penetrating oil did nothing to release the fused bolts, so this was a last-resort measure.
Larry Elmer, Kris's father, sparked up the blowtorch to cut loose some rusted and stubborn
Progress is being made. The front sheetmetal was removed and set off to the side. Now it was easier to look at what might be hiding under the skin of this vehicle.
Progress is being made. The front sheetmetal was removed and set off to the side. Now it w

Kris Elmer was amused after taking a close look at the Chevy frame. It was in bad shape. The frame was cracked in two different places, and the driver's side spindle was bent, causing some serious negative caster issues. The passenger's side of the frame was also bent and had some horrible negative camber issues. In short, it was sort of like a pretzel frame. If ever there was a candidate for a straight- axle install, this former wheel-hopping '55 was a perfect choice. There was no saving this front end.
Kris Elmer was amused after taking a close look at the Chevy frame. It was in bad shape. T
This photo is actually of a complete Jim Meyer straight-axle chassis. We couldn't find photos of a bone stock frame, so we used this one to illustrate the measurements taken. SCSS didn't trust any of the measurements from the misaligned frame, so the guys chose a different method. Typically one would establish the wheel alignment and position by the wheelbase of the vehicle in question. In this case, the '55 Chevy had a 115-inch wheelbase. Measuring diagonally from corner to corner in the center of each hub is the typical method for determining where the new wheels and axle will sit.
This photo is actually of a complete Jim Meyer straight-axle chassis. We couldn't find pho
Here's how they did it. First they located the factory jig holes on the frame in the front and the back. A measurement using the jig holes as a reference point was taken from left to right in the back, and from left to right in front. Then the center of these jig hole measurements was established. Luck was on our side-when the laser sight was used, the centers lined up perfectly. We now knew the rest of the frame, minus the front, was accurate and in good shape as far as alignment goes. We then measured 115 inches from the center of the hub on the rear axle to the center of the front hub on both sides of the vehicle in order to determine the factory wheel position and centerline. That factory wheel position was where we planned to install the new straight axle. We all like altered-wheelbase cars, but not an accidental altered wheelbase through poor measuring.
Here's how they did it. First they located the factory jig holes on the frame in the front

Using a plumb bob and micrometer to check the hub centerline, the SCSS crew made one more measurement, using the traditional diagonal measurement style to double check themselves.
Using a plumb bob and micrometer to check the hub centerline, the SCSS crew made one more
After all the measurements were taken, checked, and re-checked, a marker was used, and the horizontal and vertical lines were drawn on the floor for future reference. Since the car was on jack stands and leveled, there were no worries about where to place the new axle and wheels.
After all the measurements were taken, checked, and re-checked, a marker was used, and the
Now the fun begins. Kris used a plasma cutter to snip the front of the '55 off. This is the point of no return; if we weren't committed in the beginning, we sure were now.
Now the fun begins. Kris used a plasma cutter to snip the front of the '55 off. This is th

When the front of the original frame was cut off, it was deliberately cut too short. More metal can always be trimmed back to fit the new piece. The new straight axle clip was placed under the frame and mocked up in order to see how much more metal needs to be shaved off.
When the front of the original frame was cut off, it was deliberately cut too short. More
After further cutting, this is the result. More was taken off the bottom than the top, and this gave us some wiggle room for leveling the clip.
After further cutting, this is the result. More was taken off the bottom than the top, and
The very ends of the new clip were also clearance-cut in order to make it easier to fit into the channels in the old frame.
The very ends of the new clip were also clearance-cut in order to make it easier to fit in

Once again the same methodical process of measuring, using a laser level and plumb bob are used in order to match the new frame to those of the previous measurements. The frame and axle center were aligned to the measurements and lines that were drawn on the pavements surface. After the vehicle is built, the only wheel alignment that can be performed is toe in or toe out. Prior to the finished product, all alignment has to be built into the suspension. The reason for all the re-measuring is to take into account all the tolerances of the new frame. The geometry of the new parts needs to match the geometry of the old. Once all that is figured out, it's full steam ahead.
Once again the same methodical process of measuring, using a laser level and plumb bob are
Now the frame can be tacked into place and checked again if need be.
In order to provide more support to the weld joint, a small patch panel was fabricated by the shop and tacked into place just behind the spring bracket. This added surface area for the weld will greatly increase the frame strength. We later found out that these pieces were included in the kit, but were somehow missed.
In order to provide more support to the weld joint, a small patch panel was fabricated by

This added surface area for the weld will greatly increase the frame strength. We later found out that these pieces were included in the kit, but were somehow missed.
This added surface area for the weld will greatly increase the frame strength. We later fo
Now that the entire front clip is welded into place, Kris and Larry assembled and mocked up the rest of the components to see just how everything would align. In this photo you can see what looks to be two possible spring locations for height. However, the lower hole is the correct size and location. The center hole is there for looks.
Now that the entire front clip is welded into place, Kris and Larry assembled and mocked u
The Super Bell axle and spindles were also temporarily assembled and installed. Just like the springs, the axle also has two possible locations. The axle can be set on top of or below the springs. Below the springs will give the front end a higher ride height, while on top of the springs will give it a lower altitude. Since the springs were installed higher, it was decided to install the axle to bring the height down by a few inches.
The Super Bell axle and spindles were also temporarily assembled and installed. Just like

Before any of the steering was assembled, here's where we're at: First off, it was amazing to watch the methodical installation performed by Kris and Larry Elmer. Every part in the Jim Meyer kit worked exactly as it was supposed to work. During the install and assembly, Larry Elmer kept remarking what a well-engineered set up Jim Meyer made. Back in the day, Larry built a straight-axle '55 Chevy from scratch. He said our five-day project took him two months back then.
Before any of the steering was assembled, here's where we're at: First off, it was amazing
While the Jim Meyer subframe comes complete with a Vega steering box, we used one of Classic Performance Product's (CPP) units. We also got the optional telescoping double D steering shaft, Borgeson U-joints and ididit column from CPP, which had them on the shelf and readily available for next-day delivery to our shop in Utah. You can also purchase the item directly from Jim Meyer.
While the Jim Meyer subframe comes complete with a Vega steering box, we used one of Class
No need to worry about drilling holes into the frame for the Vega box.

The ididit column from CPP went in like it came from the GM factory back in 1955.
Once the column was in, the double D shaft was trimmed down and the Borgeson U-joints are installed on the shaft. It turns out we didn't need to use the telescoping shaft. There just wasn't enough room.
Once the column was in, the double D shaft was trimmed down and the Borgeson U-joints are
The one thing that didn't come in this kit was brackets for the brake hose. Kris did a splendid job at fabbing up a set.
The one thing that didn't come in this kit was brackets for the brake hose. Kris did a spl

Once everything was assembled, the engine was installed to weigh down the suspension and check out the work that was performed. After this, it was all taken apart again while more finishing touches were added. Even the headers cleared the steering shaft. Score one for us-that's one less headache to deal with.
Once everything was assembled, the engine was installed to weigh down the suspension and c
With the engine pulled out, it was time to set the caster angle of the axle and spindles. We called the Jim Meyer tech line and asked them what they recommended. We were told to set it between 5 and 8 degrees. We set it at the maximum of 8 degrees.
With the engine pulled out, it was time to set the caster angle of the axle and spindles.
With the caster set, the spring pads were TIG-welded into place. As before, Kris would often switch sides while welding from left to right in order to avoid heat buildup and warping the axle.
With the caster set, the spring pads were TIG-welded into place. As before, Kris would oft

The last bit of welding that was performed on the frame was the addition of some reinforcement plates. It couldn't hurt to make sure the frame was solid as the Rock of Gibraltar.
The last bit of welding that was performed on the frame was the addition of some reinforce
The vehicle was rolled outside and the bare metal frame was doused with self-etching primer, along with all the other parts. After the primer dried, it was painted in a semi-gloss black.
The vehicle was rolled outside and the bare metal frame was doused with self-etching prime
While the paint was drying, Larry went ahead and assembled the Wilwood brakes, packed the bearings, and made sure everything was ready to go once the paint dried. The Wilwood disc brake system kit came with everything we needed and went together with ease. These modern wonders are going to help our '60s-look gasser safely stop like a much newer car.
While the paint was drying, Larry went ahead and assembled the Wilwood brakes, packed the

In the meantime, Kris spent a fair amount of time custom-fabricating and installing all the new brake lines and bleeding the system. This is the final shot before the engine goes back in permanently. What a fantastic-looking project this turned out to be.
In the meantime, Kris spent a fair amount of time custom-fabricating and installing all th
All the sheetmetal is put back on and this is the view from the front.
Here's that all-important nostalgic '60s gasser stance that looks oh, so cool! The wheel placement is perfect-all that careful measuring paid off.
Here's that all-important nostalgic '60s gasser stance that looks oh, so cool! The wheel p

After all the king's horse and all the king's men put the Chevy together again, the only hiccup we ran into was the radiator position. Notice how close it is to the pulley, leaving no room for the fan. That problem was easily solved by moving the radiator to the other side of the core support. Now it's time to uncork the headers and upset the neighbors.

SOURCES
Borgeson 187 Commercial Blvd. Torrington CT 06790	Jim Meyer Racing www.jimmeyerracing.com
Classic Performance Parts (CPP) www.classicperform.com	Salt City Speed Shop
Ididit Inc www.ididitinc.com	WILWOOD ENGINEERING 4700 Calle Bolero, Dept. SC Camarillo, CA 93012