Tire Pressure Monitoring System - Low-Pressure Situation

Resetting Your C5/C6's Tire-Pressure-Monitoring System

James Berry Jun 1, 2009 0 Comment(s)

Step By Step

A flashing warning light indicates that a problem has been detected in the TPMS. Common problems include a bad pressure sensor (shown in the opening photo), a defective keyless-entry receiver module, a fault in the TPMS or body control module (BCM), or wiring problems in the keyless-entry/TPMS/BCM circuit.

C4 systems use a transmitting wheel sensor held in place by a band clamp. Each sensor has a separate identification color and frequency.

If you have an aftermarket wheel that will not accept your C5/C6's valve-stem-mounted wheel sensor, don't despair. The sensor can be mounted on the inside center of the wheel, similar to the C4 configuration. Some aftermarket companies, such as Forgeline, offer a bracket system if you don't want to use epoxy on your sensors.

The C5 and C6 wheel sensors have a built-in valve stem inserted from the inside of the wheel through a hole in the rim. It's retained by a nut and sealed with a grommet. Each sensor contains its own lithium battery with a design life of 10 years.

When replacing the wheels, you'll need to install the sensors from your original wheels onto the new ones. New grommet kits are available, if needed, to help reseal your sensors.

This sensor has been ruined by tire-mounting equipment. Be sure that your tire center has the correct equipment and is experienced with late-model Corvettes.

Since September 2007, federal law has required that every new domestic passenger vehicle with a gross vehicle weight rating (GVWR) of 10,000 pounds be factory-equipped with a tire-pressure-monitoring system (TPMS). The legislation requires that the system indicate when one or more tires has deflated beyond a preset threshold, usually 25 percent below the manufacturer-recommended pressure.

This mandate grew out of the Transportation Recall Enhancement, Accountability, and Documentation (TREAD) Act, which passed in November 2000. TREAD was the result of congressional hearings prompted by a spate of rollover accidents involving Ford Explorers equipped with certain Firestone tires.

There are two types of TPMS: direct and indirect. Indirect systems use the vehicle's wheel sensors to compare the turning circumference of each tire with that of the other three. These systems aren't very accurate and will not issue a warning if all four tires lose air equally, as might happen when outside temperatures drop. For these reasons, indirect systems have mostly fallen out of use.

Direct systems, such as the ones used in Corvettes, use sensors fitted inside the tire's air chamber, where they read pressure directly. The C4 system uses a transmitting wheel sensor held in place by large band clamp. Each sensor has a separate identification color and frequency, which is transmitted as the wheel turns. The movement of the wheel provides the energy necessary to power the transmitter. If the tire pressure drops below 25 psi, the sensor stops transmitting to the receiver, and the "Service LTPWS" lamp illuminates. The sensors don't require batteries, and the receivers don't need to be reprogrammed.

The C5 and C6 systems use a transmitting wheel sensor attached to the tire's valve stem. A separate sensor/transmitter in each wheel shares its receiver with the keyless entry system. The receiver is programmed at the factory to recognize which sensor is at each wheel location. If the tires are rotated, a sensor is replaced, or the system simply loses its calibration, a warning light will illuminate in the instrument panel. At this point, the receiver must be reprogrammed.

Fortunately, reprogramming the receiver on a C5 or C6 is a simple task you can perform anywhere, whether at home or at the track. The C5 system can be reprogrammed using either a strong magnet or a wheel-sensor-reprogramming tool; the C6 system requires the latter method.

Follow along now as we cover the reprogramming procedure for both cars.

Special thanks to Gerhard Bunge at Eckler's Corvette Parts.

If you rotate your tires or replace a wheel sensor, your tire-pressure-monitoring sensors will need to be reprogrammed. The following is a step-by-step procedure for reprogramming the C5 sensors:

1. Let the vehicle sit for two minutes; then turn the ignition on.

2. Press the "Reset" button to clear any Instrument Panel Cluster (IPC) warning messages.

3. Press and release the "Options" button on the Driver's Information Center (DIC) and scroll through the display options until the IPC display is blank.

4. Press and hold the DIC "Reset" button for 3 seconds.

5. Press the "Options" button again until the "Tire Training" message appears.

6. Press the "Reset" button until the "Learn Left Front Tire" message appears on the IPC.

7. Place a large magnet over the left front valve stem. The horn will sound, indicating the left front TPMS sensor is programmed. If this takes more than 15 seconds, pull the magnet back and try again. If the procedure fails after three tries, you'll need to start the sequence over from the beginning. GM sells a special U-shaped magnet specifically for this job (PN J41760), but a large speaker magnet will usually work just as well.

8. When the horn sounds, the IPC will direct you to move on to the next sensor. (The sequence is left front, right front, right rear, left rear.) The programming can be canceled at any time by turning the ignition off. If the programming is cancelled with fewer than four sensors learned, it will only accept the sensors programmed up to that point.

The following is a step-by-step procedure for reprogramming the C6 Corvettes sensors. This procedure requires a wheel-sensor-reprogramming tool:

1--6. These steps are the same as for the C5.7. Install the wheel-sensor-reprogramming tool over the left front valve stem. The horn will sound, indicating that the left front TPMS sensor is programmed. If this takes more than 15 seconds, pull the reprogramming tool back and try again. If the procedure fails after three tries, you'll need to start the sequence over from the beginning.

8. When the horn sounds, the IPC will direct you to move on to the next sensor. (The sequence is left front, right front, right rear, left rear.) The programming can be canceled at any time by turning the ignition off. If the programming is cancelled with fewer than four sensors learned, it will only accept the sensors programmed up to that point.

Sources

Forgeline
Dayton, OH 45439
800-886-0093
http://www.forgeline.com
Mid America Motorworks
Effingham, IL
866-866-0856
http://www.mamotorworks.com
OTC Tools
Owatonna, MN
800-533-6127
www.otctools.com
« Prev 1 2 Next »

MORE PHOTOS

VIEW FULL GALLERY

COMMENTS

TO TOP