402 Big-Block Rebuild, Part 4 - 1967 Chevrolet Chevelle SS

We put the top end together on our 402, and discuss how to break-in a flat tappet camshaft.

Patrick Hill Jan 24, 2014 0 Comment(s)
View Full Gallery

Last month, we put together our 402's short-block with forged internals from Lunati and Wiseco, and went over how to set up bearing clearances, ring gaps, and other essentials for assembling an engine that will hold up under the rigors of a heavy right foot. This month, we'll put together our top end, and go over a process that has become hotly debated in recent years: breaking in a flat tappet cam.

More than a few readers are probably wondering why we went with a flat tappet cam in the first place. Why not a "modern" roller valvetrain that will make gobs of power? Well, first, roller cams aren't exactly modern. Most people don't realize that roller cams in engines go back to the early part of the 20th century, and are just as old as flat tappet cams. The first aftermarket roller tappets came out in the ‘50s, designed by Bruce Crower. By the ‘60s, most of the performance valvetrain companies had roller cams and lifters in their product lines for use in racing and hardcore street applications. But these were expensive, and flat tappets still ruled the world.

It wasn't until the late-'80s when roller cams became standard from the factory that their affordability in the aftermarket started to increase, and almost 30 years later roller cams are as common as flat tappets, but they still haven't been able to depose them as top dog, sales-wise. The reason still comes down to cost. When going to a roller cam, you're typically looking at an increase in cost of build between $1,500 to $2,000. That includes the cam, lifters, pushrods, valvesprings, retainers and locks, and cam button spacer. For the engine builder on a budget, that is a hefty price increase.

Flat tappet cams still offer great power, but on a more budget friendly level. And for racers who compete in classes where rules specify them, flat tappets are the only option. So, in sticking with our theme of a real world, budget-friendly big-block build, we chose a flat tappet cam. Specifically, we went with a mechanical/solid lifter cam, for that old school feel.

The main issue with flat tappet cams today is their break-in procedure. Twenty years ago this wasn't a problem. But the EPA tightened standards on motor oil and forced companies to remove most of the heavy metals that were in the oil, so breaking in flat tappet cams became problematic. Zinc and other ingredients in oil were having a negative effect on certain factory emissions control equipment. These metals were critical for initial flat tappet break-in. Without them, the break-in procedure wouldn't go properly, and you'd end up with a cam lobe (or several) wiped out.

Thanks to the performance lubricant companies, this is no longer a problem. Special "heavy metal" oils are now readily available from Comp Cams, AMSOIL, and others that help ensure cam break-in goes smoothly …as long as the break-in procedures are followed.

1967 Chevrolet Chevelle Install Lunati 2/23

1. First up is dropping our Lunati mechanical lifters (part no. 70984) in place. Moly paste (included with the cam kit) is used on the lifters to protect them during initial start up before oil pressure comes up. The moly paste also helps to protect the lifter face while it burnishes to the cam lobe. Even though they're called flat tappet, the face of the lifter actually has a slight crown to it. The lifter spins on this crown, on the cam lobe.

1967 Chevrolet Chevelle Cometic Gasket 3/23

2. Part of our Cometic gasket kit is Cometic's MLS (Multi Layer Steel) head gaskets. MLS gaskets are comprised of multiple layers of stainless steel, giving them increased strength and creating the ability to rebound and resist corrosion. The outer layers are embossed and coated on both sides with Viton (a flouroelastomer rubber based material heat resistant to 250 C/ 482 F). Viton is designed to meet the demands of a variety of harsh sealing environments, load conditions, and surface finishes. The center, or shim layer, is uncoated stainless steel, which can be varied to accommodate multiple thickness requirements, such as controlling compression ratio.

1967 Chevrolet Chevelle Clean 4/23

3. Our heads were fully cleaned, then the seats enlarged to accept the bigger factory 2.190 intake and 1.880 exhaust valves, over the stock 2.065-inch intake and 1.725-inch exhaust valves. The factory cast iron valve guides were tight and showed no signs of needing replacement, so they were just cleaned up, checked for burrs, and prepped for our new valves.

1967 Chevrolet Chevelle Three Angle Valve 5/23

4. Our valves had a three-angle valve job done on them. A three-angle valve job increases flow performance of a head by giving the valve three different faces to seal against the valve seat. This process also helps smooth out flow around the face of the valve, keeping the air/fuel charge from slowing down while going around the valve face. If the charge slows down, that's power lost by not having as much of a charge in the cylinder as possible. The faster the flow, the more of a charge you can get in the combustion chamber while the valve is open, increasing horsepower.

1967 Chevrolet Chevelle Light Bowl Work On 6/23

5. Jason does some light bowl work to the heads to make sure the valves aren't shrouded, thereby restricting flow.

1967 Chevrolet Chevelle Port 7/23

6. Jason also did some port matching work to the intake ports on our heads, so they would match up better with our Cometic intake gaskets and give us some extra flow.

1967 Chevrolet Chevelle Install Pushrod 8/23

7. Time to assemble our heads. First, Jason installs our new pushrod guideplates, and screw in rocker arm studs. On the rocker studs that go into the intake ports, Jason uses non-hardening thread sealer to make sure there are no vacuum leaks, and to keep any oil from seeping into the intake ports.

1967 Chevrolet Chevelle Check Valvespring 9/23

8. Next, Jason uses a valvespring micrometer along with a valvespring cup, retainer and lock to check what height the valvesprings will install at. The springs themselves are spec'd out at 142 pounds on the seat (when the valve is closed) at a height of 1.940 inches. The cam calls for between 120-130 pounds on the seat. After measuring with the retainer, our height came out to 1.949 inches. This means the springs will set up a little taller than spec, giving us a light enough seat pressure to work with our cam. If the measurement had been too short, we would've needed a set of valve locks that would move the retainer up, decreasing seat pressure. If the measurement had been too tall, we would have needed special valvespring shims (easily available from any cam company) and shimmed the spring up to get the required seat pressure.

1967 Chevrolet Chevelle Valvespring 10/23

9. With our measurements set, Jason uses a valvespring compressor to compress the spring so the locks can be installed. Our valvesprings have a max lift of .794 inches, well below the .550-/.570-inch lift of our cam. This means we won't be anywhere near coil bind. Running a spring constantly near coil bind can overstress the spring and cause it to fail prematurely.

1967 Chevrolet Chevelle Install 11/23

10. With the heads fully assembled, they're set down on the block. With our combustion chamber size, pistons, and head gasket thickness, our net compression should be right around 10:1, safe for pump gas but still capable of great power.

1967 Chevrolet Chevelle Install Arp Head 12/23

11. With the heads in place, our ARP head bolts are installed, after using thread sealer on the bolts that go into the block's water jackets. If you don't use sealer on these bolts, you could end up with water seeping into the oil and combustion chamber. On the bolts that don't hit water, ARP's thread lube was used, along with using it under the heads of all the washers.

1967 Chevrolet Chevelle 13/23

12. When installing head bolts, make sure the washers are oriented in the correct position. The chamfered edge should be towards the bolt head. They go this way so a stress point isn't created under the bolt head when it's torqued down. The head bolts are tightened down in three steps to 70 ft-lbs, 23-46-70. The order to torque the bolts in is available online, or in any service manual for a car that had a big-block. All Mark IV big-blocks use the same sequence.

1967 Chevrolet Chevelle Torque 14/23

13. With the heads torqued down, the Lunati one-piece pushrods (part no. 8200-16) are dropped in place. These will give us excellent valvetrain stability, thanks to their stiffness. If a pushrod has flex, not only can it create a power-robbing harmonic in the valvetrain that can lead to a failure, it also won't open the valve all the way. On a big-block, the intake pushrods are shorter than the exhaust pushrods. If you get them mixed up, you won't be able to set the valve lash properly.

1967 Chevrolet Chevelle Lunati 15/23

14. After putting a dab of AMSOIL assembly lube on the tip of the pushrod and the valve stem, the Lunati aluminum roller rockers (part no. 85350) are set on their studs. The rockers feature an extruded body made from aircraft quality aluminum, with a full roller trunnion, and the bodies are machined for valvespring clearance. We stuck with the stock big-block ratio of 1.7, but they are available in a 1.8 ratio.

1967 Chevrolet Chevelle Polylock 16/23

15. The polylock adjusters are hand tightened to the point where the pushrod can still be rotated with just two fingers with a little resistance. Since this is a solid lifter cam, we don't need to worry about lifter pump up to accurately set lash. Our cam calls for a cold lash setting of .020 thousandths on the intake valve, and .022 thousandths on the exhaust. On startup it will be a little noisy, but once the valvetrain heats up and metal expands, the lash will tighten up significantly, and the valvetrain will quiet down. This is normal with a mechanical cam, and the lash settings are set according to the cam profile, taking into account metal expansion.

1967 Chevrolet Chevelle Feeler 17/23

16. To set lash, Jason uses a feeler gauge. For the intake valves, the engine is turned over by hand until the exhaust valve has just closed. To set the exhaust valves, the engine is turned over until the intake valve just starts to open. This ensures (on both valves) that the lifter is on the base circle of the cam lobe, so the lash setting is accurate. Once lash is set, the polylocks are tightened on the rocker arm adjusters.

1967 Chevrolet Chevelle Harmonic 18/23

17. With cold lash set, we moved on to other parts of the engine. First, the timing cover was bolted in place, followed by installation of the harmonic balancer.

1967 Chevrolet Chevelle Vavle 19/23

18. After rotating the engine by hand one more time to make sure there was no interference in the valvetrain, the valve covers were bolted down, then our freshly cleaned and painted intake. We're going to start out with the factory cast iron intake for our first tests, but later on will upgrade to an aluminum one.

1967 Chevrolet Chevelle Number One 20/23

19. With the intake secured, the number one cylinder was rotated to top dead center (TDC) and the distributor installed, with the rotor pointing towards the number one cylinder. This will get the timing as close as possible until we get it fired up and set it exactly with a timing light.

Holley 750 Cfm Double 21/23

20. Our factory intake is flanged for a Holley carb, and for break-in we're using this Holley 750 cfm double pumper. We'll dial in our carb selection on the dyno in our next installment. For now, we know this carb works well, and will be just fine for the break-in procedure. A word from Jason, "You can turn the idle stop screw on the carb up a few turns just to make sure it will not just fire up, but get up to the right rpm quickly. You don't want to spend too much time cranking the engine before it fires, otherwise you'll wipe the break-in lube off the camshaft."

Comp Cams Break In Oil 22/23

21. For break-in we're using Comp Cams specially formulated break-in oil. Its proprietary additive package includes optimum amounts of ZDDP (Zinc and Phosphorous), Molybdenum and detergents, so the metal surfaces of the camshaft and lifters are fully protected while they burnish and mesh together during break-in. Once the engine is fully broken-in, we'll switch to AMSOIL's full synthetic Z-ROD high zinc oil to make sure we get long life out of our flat tappet cam.

402 Engine Start 23/23

22. At this stage, start up is very critical. You don’t want to have the engine cranking for a long amount of time, as it will greatly increase the odds of ruining the cam. Jason uses starting fluid, primes the carb, and gets his engines to fire up as quickly as possible. “Once it is running, you need to bring it right to 2,000 rpm, and run it for 20 minutes minimum. You don’t need ot keep it at exactly 2,000 rpm the whole 20 minutes. Varying the rpm keeps oil going to different areas of the engine, splashing it off the crankshaft at varying engine speeds.” says Jason. The first 10 minutes of run time are critical for cam break-in. With break-in complete, the oil is drained and inspected for any signs of metal in the oil. Then the oil filter is removed, cut apart, with the filter material inspected for metal shavings. Both were clean, meaning our big-block was good to go! Next up, we’ll hit the engine dyno to get the engine dialed in, and play around with some different things to see how they affect power.

Sources

AMSOIL
Superior, WI 54880
800-777-8491
www.amsoil.com
Summit Racing
Akron, OH
800-230-3030
SummitRacing.com
Auto Metal Direct
Buford, GA 30518
866-684-5942
www.autometaldirect.com
Cometic Gasket
Concord, OH 44077
440-354-0777
http://www.cometic.com
Lunati Camshafts
Olive Branch, MS
662-892-1500
www.lunatipower.com
Bad Attitude Engines
352-528-5386
http://www.badattitudeengines.com
Rollins Automotive
352-335-7223
http://www.rollinsautomotiveinc.com
« Prev 1 2 Next »

MORE PHOTOS

VIEW FULL GALLERY

COMMENTS

subscribe to the magazine

get digital get print
TO TOP