Does your garage reek of gasoline fumes? Seldom-noticed parts in your Corvette make your garage smell better and make the air cleaner. The Evaporation Emission Control system, EVAP or EEC, also called Evaporation Control System, ECS, became a part of many cars’ inner workings in 1970. It is one of the most benign pollution control systems with a relatively low cost and with no impact on performance. EVAP hasn’t gotten the attention or respect it deserves. Vette will help correct that problem with a look at this little understood system.
In the early ’70s, the smog control devices added to cars were scorned by most performance enthusiasts. People in rural environments wondered what the fuss was all about, unless they flew into L.A. and saw the fiendish-looking brownish cloud blanketing the valley. In this era it was quite common for owners to remove the Air Injector Reactor (AIR) pump and its tubing, Exhaust Gas Recirculation (EGR) valve if the intake manifold was changed, and the catalytic converter after its debut in 1975. Swept away in this rush to restore performance often were the EVAP canister and its hoses. Only the Positive Crankcase Ventilation (PCV) valve was usually untouched.
Hydrocarbon emissions are a principal cause of smog. Prior to the ’60s, fumes from the interior of the engine, which are heavily laden with hydrocarbons, were fully vented to the atmosphere by a large road-draft tube and a vented breather cap. These hydrocarbons came from gases blowing by the rings and valveguides and the hot engine oil being whipped up by rotating components. The PCV system allowed these fumes to be drawn into the intake manifold to be burned.
EVAP did the same for the gas fumes from the gas tank. In prior years, gas tank fumes were allowed to escape into the atmosphere. This was the era of the fully vented gas caps. The EVAP system’s function was and still is admirable. It keeps these completely unburned hydrocarbons out of the atmosphere. A little gas evaporating now and then might seem like a minor issue but it’s not.
When a fuel tank is not sealed, fumes escape 24-7, even when the car is parked. This alone can contribute as much as 20 percent of a vehicle’s total pollution. It’s been widely reported that Sun Oil Company research showed that a vehicle with a fully vented, missing or inoperative fuel cap allows 22 gallons of gasoline to evaporate over a 1-year period. Note that these fumes are completely unburned hydrocarbons so they are much worse for smog than the almost completely burned hydrocarbons emitted from the exhaust of a modern automobile. That’s why modern cars produce an error code (DTC) if the gas cap is not properly sealed.
Here’s how the EVAP system works. Fumes from the gas tank go into a storage canister where activated carbon absorbs the fumes. When driving, a small amount of outside air is drawn through the canister. The air removes the stored gas fumes from the carbon, takes them into the intake manifold and from there they burn along with the main air/fuel mixture. This makes your garage smell better and keeps the air cleaner. The EVAP system is fairly simple and its parts are relatively inexpensive.
For the first few years, Corvette EVAP canisters employed a valve on top that opens when the engine is running above idle to allow manifold vacuum to draw air through the canister. At idle, the valve is closed so that the extra air and vapors don’t upset the idle mixture. At higher rpms more air is going through the engine and the EVAP has little effect on the mixture. The manifold vacuum supplied to the canister on the early systems comes from a hose that runs to the T-connector at the PCV valve. The canister valve is controlled by the level of vacuum it receives from the small hose that goes to the timed port on the carburetor.
Other canister components include its activated carbon and, on the first systems, a filter at the bottom to keep dirt and debris from getting into the carbon. The carbon works effectively for many years, but it also can be replaced on the early canisters. The third hose goes from the canister to the steel tubing, which runs along the left side of the frame rearward to the gas tank.
At the gas tank on 1970-’74 Corvette EVAP systems, a fuel separator valve is bolted onto a bracket near the top of the tank’s left side. A 3/8-inch hose on the bottom of this valve connects to a vent tube on the top of the tank and a 1/4-inch hose at the top connects to the steel tubing. The fuel separator valve has a float inside that closes the valve when gas floods the valve. This can happen from fuel sloshing in the tank or if the car was parked on an extreme angle. The valve prevents liquid fuel from entering the tubing and overwhelming the storage value of the canister.
A new type of gas cap was introduced for the EVAP system. It’s stamped “SEALED” on early models and it seals the inlet, except in the unlikely case when it can vent if the pressure in the tank gets high enough. The only time high pressure will occur is if a blockage occurs in the EVAP system.
If your Corvette has seen many seasons or gone many miles, it’s worth checking the EVAP system to make sure it’s working properly. The components of the system are hidden from view but it performs an admirable service. And it does so reliably, at a low cost and with no drag on performance or fuel mileage.
01. The heart of the EVAP system is a canister filled with activated carbon. The carbon absorbs gas fumes from the tank and stores them until being released and drawn into the intake to burn with the engine’s air/fuel mixture. Early canisters had an external valve on top.
02. The carbon inside the canister stays effective for many years. With early EVAP canisters, the carbon can be removed and replaced. A common source of activated carbon is aquarium supply stores for their filters.
03. A virtually unknown filter is under the lower cover and cleans the air going into early EVAP canisters. The factory service manual says to change the filter at least every 24 months or 24,000 miles. I’ve never seen or heard of one being replaced, but they are available.
04. Canisters are still available for mid-’70s EVAP systems. Corvette Central lists this canister for all 1974-’77 models. By then, the EVAP system dispensed with the vacuum valve on top.
05. A fuel vapor separator valve mounts on the side of the gas tank at the top on most 1970-’74 Corvettes. The good news is that new ones are available. The bad news is that it’s a chore to access for inspection or replacement.
06. To test the valve, blow air through either port. The valve is open and air should flow freely through both ports when in its normal position as mounted on the tank. When positioned up-side-down as shown, the valve should close and permit no airflow through the ports.
07. Gas caps changed to non-vented on EVAP-equipped cars. In the early ’70s, the caps were stamped “SEALED.” The cap’s gold dichromate coating is fragile. Replacing an old tarnished cap with new is an inexpensive way to brighten up those gas station stops.
08. The hoses in the EVAP system should be labeled “FUEL VAPOR” or “PCV/EEC.” It takes a tougher rubber to handle fuel vapors than those designed to handle just gas, oil or coolant.
09. EVAP hoses with clamps are available for connecting the vapor line on the frame to the canister and at the other end for connecting to the fuel separator valve.
10. Decades of exposure to engine compartment heat and fumes take a toll on the rubber hoses of the EVAP system. Tip: use a razor blade or utility knife to cut an axial slit in the hardened hoses. That can prevent breaking the plastic nipples on the vapor separator valve or PCV T-fitting.
11. Air is drawn through the canister into the intake manifold via the T-fitting at the PCV valve. The PCV valve serves the same function as the EVAP system by preventing hydrocarbons from venting to the atmosphere. Check these hoses and their connections. Engine compartment heat and fuel vapors can harden and crack the rubber causing vacuum leaks.
12. Also inspect the rubber grommets that seal the PCV valve and the breather pipe to the valve covers. When these harden or crack, fumes can escape and dirt can get into the engine. On the right is a grommet for steel valve covers, which has a narrower groove than grommets for aluminum covers.
13. When accessing the canister, it’s a good idea to order new seals for the splash shield. This rubber is likely to be in sad shape, too. Use weatherstrip adhesive to attach the rubber to the shields and, if originality is a concern, reinstall the factory seal staples. Black oxide-finished body bolts with captive washers are also available for the shield and canister bracket.
14. The fuel separator valve bolts to a bracket on the top left side of the gas tank on early systems. Even if your EVAP system is not connected now, consider buying the original tank. The tank vent tube can be blocked off and a vented cap used until the system is restored.
EVAP Canister R&R
15. Can you spot the EVAP canister? It’s well hidden on early ’70s Corvettes, located far out of the way under the windshield washer fluid tank.
16. Remove the rocker molding to access these splash shield bolts. Try hard not to break the molding screws or strip their heads. These screws are exposed to the elements and their machine threads are often rusted. Next, remove the splash shield. Again, apply penetrating oil to the exposed threads of the bolts. It’s important to try not to break loose the weld nuts.
17. Remove the three canister bracket bolts. Here too, apply penetrating oil on exposed bolt threads and try to not break the weld nuts loose. Be careful. Too much torque on the bolts will twist and distort the thin metal bracket.
18. Note the alignment of the hose nipples to the bracket and mark this position on the canister so that when it is installed, the hoses will face the correct direction. Install the splash shield and the rocker molding to complete the job.