Balance Rotating Assemblies

Why Getting Every Engine Balanced Is Important

Jake Amatisto Jan 13, 2014 0 Comment(s)
View Full Gallery

We recently got to hang out with the guys from West Coast Balance in Santa Ana, California, to learn about the procedures they use to meticulously balance rotating assemblies—everything from high-powered drag racing monsters to high revving endurance combos and everything in between. In these days of stroker cranks, lightweight rods and pistons, engine balancing is even more important. And while the aftermarket cranks from overseas are strong and affordable, they require balancing if you want your engine to last.

Shop operator Andy Maron has been balancing rotating assemblies since the late 1970s and got his start on diesel engines, but these days, his SoCal shop is geared towards high-performance and racing engines. The procedure starts with simply weighing the connecting rods and then the pistons to find the lightest one of each bunch. Then, the remaining rods and pistons are shaved on a belt sander to match the weight of the two lightest components. At this point, a set of rings, the pin, and the locks are weighed, as are the rod bearings. The idea is to get to total bob weight of the rod assembly. Once that number is known, brass bob weights are stacked and bolted to the crankshaft and spun up on a crank balancer. The bob weights mimic the presence of the rod and piston assembly and the crank balance machine senses where the crank either needs weight added or needs weight taken away. This becomes tricky when a customer wants to balance a stock crank with lightweight rods, or when a lower quality crank is used. It also gets tricky when you want to convert an engine with light rods to heavier ones. Maron explained, "Guys will bring in LS7 engines to convert them over to H-beam rods (likely because they want to boost them). Well, you have to compensate for that added weight in the crank, which is substantial on those, but customers ask for it."

The cost of your balance job relies mainly on not how much metal needs to be removed, but rather how much needs to be added. "We sometimes have to add a lot of weight to a crank in order to make it right, and that can get expensive." Heavy metal, or in West Coast Balance's case, Tungsten/Nickel, is inserted into the crank counter weights in order to achieve proper balance. "When we have to add heavy metal, we freeze the slugs before pressing them in," Andy said. By freezing them, they shrink by a few thousandths and can easily be pressed into the side of the counter weight. When the slugs reach ambient temperature, they expand, locking them in place; even at 10,000 rpm.

We learned that small-block Chevys can be confusing when it comes to balancing depending on if you have an early or late-model engine. Because of the one-piece rear main seal on late model SBCs, you could say the engine is sort of half-internal, half-externally balanced. The rear seal on late small-blocks rides on a large concentric journal, so there's no offset flange like on early motors. To compensate for the added weight, an externally balanced flexplate must be used, even though your harmonic balancer may be a zero balance.

2/17

1. If you do the math, a ¼-ounce of unbalance 4-inches from the center of rotation creates crazy amounts of forces: 7 lbs at 2,000 rpm, 28 lbs at 4,000, 63 lbs at 6,000 and well over 110 lbs at 8,000 rpm. This can be detrimental to the bearings and severely reduce your engine’s lifespan.

Each Component Weighed And 3/17

2. Starting with the rods, each component of the piston assembly gets weighed and recorded.

All Pieces Match Weight Of Lighest 4/17

3. Once the lightest rod is found, the other seven pieces are matched by removing material with a belt sander.

Areas Okay To 5/17

4. There are a couple areas on the rod where it’s safe to grind: the side of the big end and the very tip of the small end. It’s incorrect to grind on top of the rod cap since that area needs to be as strong as possible in order to stay perfectly round under load.

Pins Locks Rings And 6/17

5. The pins, locks, rings, and bearings also get factored into the final weight, but remember there are two bearings for each journal, so the weight of the bearing is typically just doubled. West Coast Balance also factors in half of a gram for the oil that will stick to the crank.

Tci Automotive 7/17

6. TCI Automotive offers every kind of flexplate you could want for your Chevrolet powerplant. These showcase two different styles; on the left is the late-model SBC (smaller pattern), while on the right is the early model piece. More often, stroker small-blocks require a flexplate with the external weight on it to be balanced properly.

Mahle Flat 8/17

7. As rods and pistons get lighter, getting the correct balance becomes much more critical. Our Mahle flat-tops for example, weighed .0535 grams, which is fairly light, but you can order them even lighter.

Fixtures Support Cranks 9/17

11. Two of these fixtures support the crank’s journals and are what actually sense how balanced the crank is. There’s also a magnetic degree sensor that attaches to the snout. Then, by using these inputs, the computer reveals to the machinist at what degree the crankshaft is either too heavy or too light and by how much.

Counter Weights Of V 8 10/17

8. The counter weights of a V-8 crankshaft are positioned very specifically by GM to offset the weight of the rod; everything from the bottom of the big end to the top of the piston. It’s when we start to add heavier pistons, with lighter rods and the opposite in different configurations that the engine balancing becomes crucial.

Light Welding Done To 11/17

12. If the crank only needs a little weight added, some light welding is done on the counterweight.

Total Weight Of Assembled 12/17

9. Once the total weight of the pistons assembly is calculated, it’s then matched using special fixtures that hold lead shot.

Drill Out Factory 13/17

13. At times, it’s acceptable to drill out the factory counterweight if minimal material needs to be removed.

Lead Shot Weight Matches 14/17

10. These fixtures attach to the crank journals and simulate the exact weight of your piston and rod combination.

Pistons Get Shaved Down To Lightest 15/17

14. The pistons also get shaved down to the lightest weight of the bunch. The proper area is just under the pin lock.

Spin Pistons On 16/17

15. On aftermarket pistons with short skirts, it’s acceptable to spin them in a lathe, however, on stock type pistons with long skirts, you have to lighten them by hand.

High Powered Machines For Zero 17/17

16. The guys at West Coast Balance Shop in Santa Ana, California also work with high-powered engines, so they aim to balance everything as perfect as possible. By dialing the balance machine to the smallest tolerances and by carefully adding or removing metal, their work often comes out within a fraction of a gram from being totally zero balanced.

Sources

TCI Automotive
Ashland, MS 38603
888-776-9824
www.tciauto.com
Mahle Motorsports
Fletcher, NC
888-255-1942
http://www.mahlemotorsports.com
Scat Crankshafts
Redondo Beach, CA 90278
310-370-5501
www.scatcrankshafts.com
ARP
800-826-3045
ARP-BOLTS.COM
« Prev 1 2 Next »

MORE PHOTOS

VIEW FULL GALLERY

COMMENTS

subscribe to the magazine

get digital get print
TO TOP