1964 Chevrolet Corvette - Detail Oriented

Ron Emmons' '64 Resto-Rod Hides A Panoply Of High-Tech Touches

Paul Zazarine Jul 1, 2008 0 Comment(s)
Vemp_0807_05_z 1964_chevrolet_corvette Rear_view 2/9

The tired 327 was pulled and set aside in place of an '02 LS1. Rob Basler, of Skip's Automotive in Sarasota, put together a strong, high-revving engine with lots of reliability built in. He added a Lunati 382 stroker kit, ported and polished the heads, and then flow-tested them. A Weiand/Lingenfelter intake-painted red to match the exterior-was added with a ported stock throttle body. Aaron Quintez of Sarasota fitted up the Street and Performance 13/4-inch headers and custom-bent 21/2-inch exhausts exiting from the rear valance. On the dyno, the tricked-out LS1 produced 446 rear-wheel horsepower at 6,400 rpm and 438 lb-ft of torque at 4,900 rpm.

With the rolling chassis and drivetrain completed, Ron began the search for a competent shop to complete the body, marry it to the chassis, and perform the assembly work. He also had some decisions to make about exterior features. "As we continued with the restoration," he says, "we had to decide if we were going to incorporate the 'stinger' hood and side pipes that are so prevalent with modified midyears." He made the decision to pass on both after going to a Corvette show. "The final decision not to incorporate these items came when we were at a Vette show and two midyears were parked side by side. One had the stinger hood and side pipes, while the other did not. I thought without the hood and side pipes, you get a better view of the lines and sleekness that we love about the midyears."

Vemp_0807_06_z 1964_chevrolet_corvette LS1_engine 3/9

Although Ron had hand-picked all the components for the Vette up to this point, he finally found a shop to which he could entrust the car's completion. Still, it was important to him to remain as involved as possible. "It took a year to find Mike Griffin of Sarasota," Ron says. "Mike is an exceptional street-rod builder with great attention to detail. It was a perfect setup to allow me to be involved but get the job done in a timely manner."

Griffin had to fabricate a dolly and a rotisserie in order to complete the work on the body. The old, damaged panels were replaced or repaired, and PPG Corvette Torch Red paint was applied. Next, Griffin fabricated hidden hood hinges and a removable rollbar. Once the body was mounted on the chassis, work began on installing new Painless wiring harnesses for the body, engine compartment, and interior. To deaden sound and keep the passenger compartment cooler, Griffin laid down an application of Lizard Skin, followed by a layer of Dynomat. NU Relic power windows were installed, as were the plumbing and vents for the Vintage Air A/C system.

Vemp_0807_07_z 1964_chevrolet_corvette Wheel 4/9

Custom Auto Sound's AM/FM/CD player with 10-disc changer was selected to replace the factory radio. The radio head is configured the same as stock, and the changer installs behind the seats. Ron also chose not to cut up the door panels for speakers. Instead, they were subtly placed in the top of the dash and in the rear. The factory gauges were replaced with Auto Meter's Pro-Comp Ultra-lites, which use black alphanumerics and red needles on silver faces. A traditional, midyear-correct teak steering wheel sets off the completed dash.

With all the wiring and instrument panel work completed, an Al Knoch reproduction interior was installed to maintain the classic midyear appearance. Ron chose a set of Simpson safety belts to replace the factory units.

Vemp_0807_08_z 1964_chevrolet_corvette Roadster_front_view 5/9

In total, it took about 1,000 hours over a four-year time span to complete the '64. Close inspection reveals that not a single detail was overlooked. The engine compartment, for example, is a feast for the eyes. The intake was cherried and painted exterior color. Drive accessories, such as the power-steering pump, A/C compressor, and alternator, were placed low and out of view. The Torch Red engine top and compartment are contrasted with smooth, satin-finished billet valve covers, a bright air inlet, and a polished-aluminum radiator shell.

Now that the '64 is done, will Ron drive it to work and take it on vacations as he did in the past? "It was my intention to have another daily driver," Ron says, "with the ability to play with my Cobra friends on the track. Until the newness wears off and my wife says it's OK, though, there is no track time planned." Fortunately for Ron, this is one midyear that's sure to get the blood pumping-regardless of the driving environment.


Connect With Us

Get Latest News and Articles. Newsletter Sign Up

subscribe to the magazine

get digital get print