1966 Chevelle SS - Blue on Black

It Leaves a Lasting Impression

Dakota Wentz Sep 1, 2006 0 Comment(s)
Sucp_0609_05z 1966_chevelle Front_seat 2/8

This time Joe planned things out a little more, starting with what he liked about the previous design, and went from there. The previous Chevelle had disc brakes up front and drums out back, which was a no-go in Joe's eyes. He ordered a set of Baer brakes for all corners. The Baer brakes gave him the look he was after, but only when the wheels were off. What he needed was a set of rims that would not only enhance the look of the car, but show off the brakes, as well. A set of Boyd Coddington Magnetos wrapped in Kumho rubber were picked as the new rolling stock. A set of 18x8s up front, and 18x9s in the rear not only give the Chevelle a new look, but also act as windows to see the Baer brakes resting behind them. From there, the rest of the suspension was tackled. Up front, 2-inch dropped spindles from Belltech were put on, along with Hotchkis 3-inch dropped springs, a Hotchkis 1 1/8-inch sway bar, and KYB shocks. The A-arms were blasted and powdercoated black, then outfitted with new polyurethane bushings. In the rear, KYB shocks and a Hotchkis 1-inch sway bar add stability to the '66.

Sucp_0609_06z 1966_chevelle Ss_emblem 3/8

As for the small-block, it was next up on the chopping block. Although Richard, the previous engine builder, did exactly what he said he would with the small-block, Joe was looking for something a bit more potent. The two came up with a '70 454 big-block that was ready to go under the knife. The 454 was machined to a 460 by JMS Racing Engines. Richard then began assembling the fresh block. GM Performance Parts aluminum heads, installed along with Manley 10.25:1 pistons and a COMP Cams hydraulic roller cam. Up top, a factory Corvette manifold was used in conjunction with a Holley carburetor. On the frontline rests a Zoops pulley system and Sanderson shorty headers were installed, along with Dynomax mufflers, which can be heard echoing down the road. When the engine was finished, it was put back on the dyno where it cranked out 525 hp at 5,800 rpm and 550 lb-ft torque at 3,600 rpm-a vast improvement over the small-block. Backing the Rat is a 700-R4 with a TCI 2500 stall speed converter assembled by Mike's Toy Shop in Pomona, California. Along with the tranny is a 12-bolt with Superior 31-spline axles, also assembled by Mike's.

Sucp_0609_07z 1966_chevelle Valve_covers 4/8

For the last thing on the agenda, it was back to J.V. Enterprises in Azusa, California. Joe told the owner, Vinnie, he wanted to completely redo the paint scheme. He didn't really have a drawn-out plan other than that he wanted a two-tone job. Vinnie came up with a PPG custom-mix blue combined with PPG Black. Breaking up the two-tone is a silver leaf 1/2-inch stripe highlighted in red pinstripe. Joe was sold on everything except for the black top. If Vinnie wanted to spray the top black, then Joe wanted him to mix in some blue pearl for those sunny SoCal days. The plan was set . . . well, almost. Vinnie and Joe also decided that while the engine was out, they would redesign the engine compartment, as well. The firewall and inner fender panels were reworked and smoothed. The two-tone paint scheme found its way under the hood running along the firewall. Under the hood, detailing was taken one step further when the bottom half of the polished aluminum valve covers were sprayed blue and given a red stripe around them. The inner fender panels were also sprayed blue.

If there's one thing to be said about Joe's Chevelle, it's that it most definitely leaves a lasting impression in some way, shape, or form.


Connect With Us

Get Latest News and Articles. Newsletter Sign Up

subscribe to the magazine

get digital get print